Frame #5 removed

 

 

 It's been awhile since my last post because we've had so much going on around the house that required my attention.  I also rearranged some things in my workshop/garage so that I can work.  But I'm back working today.  Bought lots of supplies and a few tools over the last month so that hopefully frame building will progress without waiting for screws, bolts, drill bits, 3M 5200 adhesive and Smith's CPES (clear penetrating epoxy sealer).  I also received some wood for the keel, chines, stringers and frames 3 or 4 weeks back.  This was in addition to the wood I already talked about and it was shipped in from White Plains NY.






Today I removed a frame and began rebuilding it. I'm excited to finally have started building up instead of constantly tearing down.  However, as usual things did not go as I envisioned.  They used a glue or something to mate the pieces together in the frame making impossible to separate.  As you can see in the next two photos, I tried to use a chisel to separate the pieces but it didn't separate along the joint as I expected.

 
 
So I had to use my jigsaw to cut the two apart.  I needed them apart so that I could trace the pieces on new frame stock.  There are three pieces so the outside two could be done without separating but the middle one had to have one side off to trace it accurately.

But at last, I cut off the easiest side and manufactured the fist piece of this frame!  It's still too thick so when I cut out the remaining pieces I'll plane all of them down at one time so they will be all the same thickness.




Comments

Post a Comment

Popular posts from this blog

Frames and bottom continued

Image
 Over the last several weeks I have continued to work on attaching the plywood bottom and the intermediate frames.  In order to do it by myself I've had to get creative.  But as of today, I have just 9 intermediate frames to go and one last piece of the plywood bottom. Here is a frame where I drew a line to line up through the hole that's drilled in the correct position.  Once I prepare the frame, I line it up through the holes.  However the one near the keel is to far away to move the frame and see in the hole.  So I attached the frame near the chine and then used a mirror to see it near the keel.    For the starboard bow plywood piece, I attached the intermediate frames before I attached the plywood to the boat.  However, this made it more challenging to be sure the plywood was in contact with the keel near the frame farthest from the bow.  So I clamped it and them piled a couple of cinder blocks to insure contact.  After this I w...
Read more

Plywood bottom

Image
 Now that the planks are bent, I've moved on to the plywood bottom.  The original had 3 pieces and now I realize why some frames were built the way they were.  The first two from the transom to amidships were fairly easy.  I left an over hang which I'll make flush later.  Here are the first two after cutting and fitting. I attached these but before moving on, I had to address a frame that was very low.  When we bent the bow planks, we noticed a dip in the board we bent.  So, I had to attach a filler to bring it up to level.  When I was doing this, I remembered that I had a low frame and put off addressing it.  Well . . . the time had come. Once this was completed, I moved on to the other four pieces of plywood.  All my friends had been telling me that the plywood would not bend in two directions near the bow so I should cut foot wide strips to install at an angle, so the plywood was only bending in one direction.  However, I had ple...
Read more

Bending bottom planks

Image
Bending the bottom planks had some challenges.  My friend Al came over to help.  At first, I started with one at a time.  This if the first 2 garboard planks steamed and bent into place. To cut out some of these bow planks I had to clamp them down to trace their shape. I also had to create an improvised soaking tub.  The last one I made was designed for the transom piece I had to bend which was much shorter.  This is what I came up with in my trailer.  Worked well because to empty it I just let the plastic down in the back and moved the trailer tongue up the hill a little.   So after the first two, Al came over to help and we did the final 6 in a couple of hours. On the starboard side I had one board that cracked a little.  I repaired it with epoxy since it will not be seen once it's on the boat.  It will be painted where the crack happened.  After I removed them to do the plywood, I noticed another which I fixed also.
Read more